The embedded recognition frame can provide item reads for retail checkout or controlled material issue. Define its read area using the actual tagged goods so that nearby stock is not included unintentionally.
The embedded recognition frame can provide item reads for retail checkout or controlled material issue. Define its read area using the actual tagged goods so that nearby stock is not included unintentionally.
The source table explicitly identifies RIA20 even though the archived filename begins RAC07. Treat the ordering-code table as the applicability evidence; RAC07 is not introduced as another product alias.
The ink element and the EAS insert perform different roles: visible tamper deterrence does not identify which electronic exit system a particular unit supports. Confirm the selected AM, RF or other specifically ordered insert before store deployment.
Use a Wi-Fi-equipped AS9010, a supported Tuya Smart application and an internet-connected 2.4 GHz router. Put the delivered controller into its documented pairing state and wait for both device and app confirmation before attempting remote setup.
Use a Wi-Fi-equipped AS9010, a supported Tuya Smart application and an internet-connected 2.4 GHz router. Put the delivered controller into its documented pairing state and wait for both device and app confirmation before attempting remote setup.
The T011B housing includes a hanging opening and a pointed attachment pin. Check both the merchandise attachment point and the required hanging clearance with an actual sample before approving the store display.
The SW002 bilingual sheet describes the standard spider-wrap configuration. Match its cable and selected EAS frequency to the merchandise and installed antenna before setting up the checkout routine.
The SW001 sheet identifies a replaceable CR2032 battery. Remove the transport insulation as instructed before commissioning, and check the alarm response again after the approved battery-replacement procedure.
This longer reference concerns the AS4026 AM antenna assembly paired with the SAC066 entrance gate. Identify the actual antenna controller, channels and supply before applying its installation or remote-controller procedure.
The SAC066 sheet describes the swing-gate component, while the longer paired reference concerns its AS4026 AM antenna assembly. Confirm the cabinet, swing arm and opening layout independently of the AM controller settings.
The SAC066 sheet describes the swing-gate component, while the longer paired reference concerns its AS4026 AM antenna assembly. Confirm the cabinet, swing arm and opening layout independently of the AM controller settings.
The CZ5000 reference calls for a warm-up of at least ten minutes before final performance assessment. Establish the correct transmitter/receiver connections and dedicated supply first, then inspect the signal state and test active tags.
The HR5900 board reference provides series, parallel and combined synchronization arrangements. Identify the actual board and synchronization lead before choosing a layout.
Use the HR500S operating and interference indicators while testing the proposed installation. Keep tagged stock clear of the passage and use the dedicated supply arrangement described for the delivered unit.
Match the supplied 95100 transmitter and receiver settings before testing the passage. Use the board-specific synchronization and wiring reference rather than the Mono setup sequence.
The Mono system adapts to the installation after power-up. Allow that process to finish, inspect the noise/status indications and test the intended tags at the final location.
Identify the installed transmitter hardware and its master/slave role before choosing cable or optical synchronization. Different optical versions have different repeater capabilities, so follow the connector arrangement for that board.
Identify the installed transmitter hardware and its master/slave role before choosing cable or optical synchronization. Different optical versions have different repeater capabilities, so follow the connector arrangement for that board.
Use the receiver's power, interference, alarm and RF-level indications to establish the site state. The RX3000 guide separates receiver gain from the alarm threshold; a change to either needs a real label test.
Use the receiver's power, interference, alarm and RF-level indications to establish the site state. The RX3000 guide separates receiver gain from the alarm threshold; a change to either needs a real label test.
A transmitter and receiver operating with inconsistent sweep settings may not form the intended RF detection system. Check their actual board and synchronization arrangement before treating reduced performance as a receiver-gain problem.
The TST9600B manual separates recognition accuracy from the choice of narrow or wide frequency sweep. Wider coverage can accommodate label variation, while its result must still be checked against ambient noise at the real entrance.
The RS4001 sheet contains separate 3920 and 4900 transmitter/receiver board references. Identify both installed boards before following any connector or configuration diagram.
Tell us the product model, hardware version and the information you need.
